Prihlásenie
  Meno:   Heslo:

Vyhľadávač

Kategórie
                         Akcia  |  Bazár  |  Novinky  |  Kontakt  |  Obchodné podmienky  |  Registrácia  |  Nákupný košík
Údaje o výrobku
Názov: Heron stavebnice 2400mm
Interné číslo: 6972
Dostupnosť: do 24-72 hodín
Výrobca: Multiplex
Cena: 166.00 €
Pridať do košíka:
  Popis tovaru
Powerful thermal or slope glider / sailplane motor to drive the motors class AXI 2814-2820. Model of highly durable ELAPOR, controlled ailerons, flaps, rudder, elevator. Kit in Rozsyp without motor. From the first performance at the fair in Nuremberg in 2015 less than a month has elapsed, the snow on the mountains still divided he not, and never can start building the newest gliders from ELAPOR from Multiplex! Heron is the younger brother of the popular glider Solius - since it appears at first glance differ new wing of greater span "mechanization" flaps and ailerons. At first glance slim body with a transparent canopy with cockpit indicated, just the T-tail configuration for easy removal of the horizontal tail for transport. The wing span of 2400 mm with elegant winglets provides excellent strength properties and pleasant behavior at low speeds. The fuselage is made of almost indestructible foam ELAPOR. The secret, which allows you to have a foam body so slim, thin-walled tube is hexagonal aluminum alloy hull reinforcement from the wing after tail. Pipe and appreciate the construction of the model - now would you might be able to build trunk curled just really exerting too much effort! Pipes are also routed extension cables rudder and elevator servos. Bow fuselage and tail further strengthens several fiberglass rods glued between the torso and the tail fin. The engine is mounted in the nose of the plastic motor mount with a universally prepared holes and slots for mounting screws - you should meet the vast majority of conventional AC motors adequate performance. Included in the kit is a spinner with grippers with collet for engines with 5 mm shaft and propeller blades 12x6 ". If you decide to use a motor with a 4 mm shaft, purchase the appropriate spinner Multiplex # 73 3500. The model can also complete a" clean "glider - in this case is supplied in the kit molding bow of ELAPOR ready for mounting hook for aerotow. Canopy with transparent" bubble "is removable, fixed with a pair of conventional plastic locks Multiplex. The bow will find enough space for the controller, power pack and receiver. rudder and elevator servos are stored in kýlovce, rudder control short straight wire rods. The wing of the model of the two-part foam ELAPOR beams of the rectangular tube of aluminum alloy, the projecting portion serves as a coupling wing. Wing halves are secured in place sophisticated pin fitting in locks on the root ribs - the pin is removed and inserted from the cabin. For the aileron servos and flaps are prepared shaft with plastic covers, ailerons and flaps (the length of reinforced thin-walled tube of stainless steel) are controlled independently by two servos with short straight wire rods. The tail surfaces are made of foam ELAPOR also reinforced with fiberglass rods. Horizontal surface is attached to the top of the fin using two screws polyamide. The landing gear is wheeled in "ASW" style, with the main wheel with a diameter of 45 mm and a sliding shoe on the tail. To drive model you need brushless motor AXI classes from 2814 to 2820 was 40-50 A regulator with switching BEC power stabilizer with continuous load capacity of at least 3 and to ensure a reliable power supply board electronics with 6 servos. To serve power Li-poly tříčlánek with capacity of 2200 mAh or more with load capacity of at least 20C. The specific type dial so that you without further reweighing best based on the correct center of gravity. To control model in distress make do with ordinary six-channel computer radio system, but the ideal is of course the use of at least seven-channel computer RC kit allows independent control of the aileron and flap servos and two roll mixing butterfly brakes (both ailerons are deflected consistently up and both flaps down) . And it's also able Affordable Flash 7 or Cockpit SX! Prepared pits corresponding servos HS-55 / HS-5055MG (Nano-S) for rudder and elevator and HS-81 / HS-82MG (Tiny-S) for ailerons. Especially if you choose the propulsion system at AXI 2820, and you want to fly dynamically and on a slope, it is recommended to install a powerful servo with metal gears. Kit includes: moldings fuselage, wings and tail surfaces of the foam ELAPOR, transparent canopy, hexagon tube of aluminum alloy and further reinforcement of fiberglass and stainless steel set of small parts and accessories, wheel, 45mm, folding propeller with 55 mm cone with grippers with 5 mm collet and leaves 12x6 "sheet of stickers and instructions.
  Technický popis tovaru
Margin [mm] 2400 Length [mm] 1100 Weight [g] 1350 - 1550 Wing area [dm2] 41.3 Controlled functions S, V, C (2) M, F (2) Building performance S1, S2 Difficulty piloting P2 Drive and RC equipment: RAY termik FOXY FOXY termik termik AXI AXI tuning tuning Motor RAY C3536 / 08 G2 C2814-850 FOXY FOXY AXI 2814/20 AXI 2820/12 G2 C2820-950 Controller RAY R-50SB FOXY R-45SB Propeller folding the sheets 8x6 "** with folding blades 12x6" ** with folding blades 12x6 "* Fold the leaves 12x6" RAY G3 Battery 11.1 V 2200 mAh Servos 2x HS-55 (M + H), 4 HS-81 (K + F) 2x HS-5055MG, 4xHS-82MG Radio Set min. 7 channel computer *) Component kit **) Requires the use of cone # 73 3500 Collet 4 mm
  Video
Vyber výrobcu
Partneri
pic pic pic pic pic pic pic pic